Kundenbewertungen für VEVOR Tischkreissäge 4400U/min, Tischsäge 1800W, 85mm bei 90° Querschnitt / 60mm bei 45° Schrägschnitt, Winkelanschlag -60˚/60˚, Ideal für Schneiden von Holz und DIY-Holzbearbeitungsprojekte

L'oggetto in questione,x il momento funziona benissimo,e sono molto soddisfatto. Spero che continui così. L'unica cosa che non mi è piaciuta,sono i tempi di consegna. Nelle inserzioni,scrivono che in 2 giorni hai l'oggetto,e invece ci mette una diecina di giorni. E questo..... lo trovo molto fastidioso. Specialmente, quando l'oggetto ti serve. Spero che in futuro,chi gestisce il settore consegne,sia più realistico,in modo tale, che una persona si può anche organizzare,nel frattempo. Grazie

Preis und Ausstattung sehr gut. Einstellung Sägeblatt schlecht. Winkel zur Längsachse/Parallelanschlag um 0,6mm verstellt. Einstellung umständlich. Verstellung der großen Schraube bewirkt seitliches Spiel am Lager. Erst durch Einstellung der Madenschraube mit 6mm Gewinde und großer Schraube Einstellung 0,0mm erreicht. Jetzt Zuschnitte in Holz sehr gut.

The only problem is with the guard of the cutting wheel (blade). When the blade is fully up the guard touches the blade. Also when the blade is low the bolt that tightens the guard interferes with the guide.

As I've stated in previous reviews, if you are not mechanically inclined and willing to make adjustments and are baffled by less than stellar assembly instructions, go ahead and spend a bunch more money for another product. The included assembly instructions are not for this exact product. Close but no cigar. The stand is pretty tricky and if not for the schematic showing centerline connections, I don't know if I'd have gotten the job done. As for the parts, the stove bolts, which have a domed head with a an area of square shank directly below the head (to lock the shaft from turning), we're supposed to fit into the square holes in the corresponding tubes (legs). But the shank was too big to fit in the sq holes. Tightening the nut enough to pull it in will collapse the thin walled tubes. So I filled down the first pair, but then said to h*ll with that and just allowed the heads to extend out beyond the tube surface. Got the stand assembled and working. Placed the plastic orange platform upon the stand in the same orientation as shown in instruction picture and made the appropriate attachments. Everything else is pretty much clear and/or self-explanatory. Issues with my particular unit: There is a stamped steel piece at the end of the table extension that is parallel to the blade and connects the extension rails. The rip fence, when moved to the extreme right side, will be over top of this part. Mine had two deformities on the outside edge. It was also installed too high so the rip fence had to be lifted up to clear the vertical edge. I removed the the offending piece straightened it and reinstalled it at the correct height. Now here is the biggest issue... the rip fence comes with a plastic part attached which is not mentioned in the manual and is only shown in one or two pics on the website. It extends onto the table and effectively cuts down the allowable rip by about 2". One of my criteria for a saw was a rip of at least 24" so I could rip plywood to any size. This part prevents that so I took it off, but what I found was that if you are ripping something that extends past the end of the fence where the lock handle is, the piece will not be parallel to the aluminum fence until it gets past the handle. This was totally unacceptable. To fix this fabrication error, I removed the two screws holding the plastic grip to the aluminum lever and filed the upper screw's head flat and down till it cleared the work. I then had to cut out a small portion of the grip, and then filed down the screw mounting surface till it also cleared the work. I no longer use the plastic fence add-on and can get the full rip as advertised. It is my belief that the mfgr probably discovered their fab error and chose to fix it by adding the plastic rip edge. That's why it is never mentioned in documentation. Other than that, the saw seems to work just fine. A bit loud, and draws quite a lot of current on startup but I wear hearing protection anyway. CHARACTER LIMIT REACHED!

The gate moves unless you use vice grips and the motor struggles with ripping boards.

Nice saw but wheels a bit shaky

My first purchase was the Vevor level package. After I discovered the quality, I was ready to order again. I'm a contractor, and I've gone through many job site table saws over the years. In my opinion, no one comes close to the Bosch table saw; however, there's a need for a lightweight and accurate alternative for service calls or quick jobs. This saw is a simple, "no fuss" saw that is light and compact. The parts are lightweight and need to be handled accordingly, but that's no concern for millwork or finishing. We are a fussy lot of carpenters, and a little TLC will make this saw last! Great saw for a fantastic price, it's definitely worth it!

Great saw for the money but you can’t rip small slices because it hits the dust cover

The machine works well, we use it mainly for cutting laminated parquet. The angle-adjustable slider does not fit exactly in its rail, it wobbles a little. Othervise the quality is okay.

Great price, great delivery. First cut with it piece got jambed between blade and fence. Found blade to be not square to table or fence. 2hrs of loosening motor and frame I got it in tolerance. Was almost 1/4 out of alignment. Now up and running good.