Kundenbewertungen für VEVOR Druckbehälter Farbbehälter Sprühfarbe Drucktopf 10 L Drucktank, 70 psi Lackierpistole Farbbehälter Φ 24 × 25 cm Spray Paint Pressure Pot Tank Paint Container Farbspritzpistolen Lacken, Flecken

Great pot. Held pressure at 45psi overnight. Great looking. Sturdy feel. Well presented. Worth the money

tolles Gerät - super Preis Leistung Verhältnis - alles bestens

Habe lange nach einem solchen Drucktopf für Harzguss gesucht. Bislang einmal ausprobiert und er funktioniert tadellos. Die Farbansaugstange muss nicht unbeding entfernt werden, aber das ergibt mehr Höhe und ist einfach (ich konnte es einfach mit der Hand rausdrehen) bewerkstelligt. Der Topf ist super stabil und sicher verpackt versendet worden. Ich habe mir noch eine Gummimatte (gibt es günstig aus recycelten Autoreifen) um den Top geklebt, damit die Flügelmuttern nicht gegen den Lack schlagen können.

Only just received pressure pot , well made ,heavy. Only had to fit carry handle. Will use for Apox resin casting . Only complaint the user manual could be beeter written.

Really works, use it for casting epoxy under pressure. The manual is not good, and I can't seem to get the paint sucktion pipe off of the lid. The build quality is very good and i have no leak over several days

Vraiment TOP. Utilisé pour mettre sous pression de l'urethane moulée dans des moules en silicone, aucune fuite que ce soit au niveau des raccords, de la jauge. Bref vraiment TOP. Aucun bricolage nécessaire, on déballe et ca fonctionne. Attention ⚠️ toute fois, le fond intérieur est arrondi, il faut trouver une solution pour le rendre plat afin que les moules ne penchent pas d'un côté.

Belle finition, facile d'utilisation très costaud. Je recommande cet article, pour ma part je l'utilise pour mise sous pression de résine époxy.

Excellent service from Vevor - numerous email notifications of order progress and next day delivery. Very well packaged and courier was excellent too, equally with email notification of progress. The unit still has the internal paint tub fitted even though it's the resin model. I tried to remove the tube by unscrewing but it was well and truly in there - resulted in cutting it off. Even heating it didn't loosen the thread lock adhesive. The chamber is very well made, excellently painted and all the valves are high quality. I used a 6 litre mini compressor (6.3CFM) to pressurise it and it took about 40 seconds to reach 50psi, from no charge in the compressor. The chamber holds it pressure and does not leak at all over an hour of testing. I have not tried it for resin casting yet (too cold in the garage - only using the compressor to blow wood dust off the beer cans!) but I have absolutely no doubt it will be brilliant. I did consider converting a paint chamber - but no point. This unit comes complete and ready to go, why have the stress, extra time and effort messing about buying the extra valves, etc for a DIY unit. This ticks all the boxes and converted ready to go. Trust me - I did a lot of research before buying.

Excellent piece of kit. Sealed lid for first time, filled it with air to 50psi. Disconnected compressor and left for 3 days. The psi was still 50, never had that before with a pressure pot. Used it several times since and still holding pressure, no leakage at all. Good quality. I cut off the liquid out pipe inside as it interfered with caddy. Excellent thanks.

Le colis est arrivé endommager et a été ouvert puis refermer (peut être par les douanes!? ) et du coup il manquais la fiole de réparation de fuite a l'intérieur du paquet, pour l'instant il ne semble pas fuir donc ce n'est pas un gros problème. La qualité de l'ensemble est très bonne et pour 110€ ne nécessite pas de faire de modifications pour les coulées de résine donc vraiment très intéressant car le rapport qualité/prix/sans modifications est introuvable ailleurs!