Kundenbewertungen für VEVOR Palettengabel 1090x70x230mm Gabelträger 907kg Tragfähigkeit Gabelzinken 109cm Gesamtlänge mit 76cm-Gabelblatt Gabelstapler 495-915mm Einstellbar Gabelstaplerzinken Frontlader Palettenrahmen

Got in touch with support. They said they’d have the parts shipped…cut to weeks later and I’m still without parts and was instead issued a partial refund despite stating the preference for accurate hardware instead. Can’t fault the equipment I received, just hope the hardware I purchased is what the equipment calls for with tolerances.

Bought with high hopes. The one pin to screw on isn’t screwing on properly. Needed a hammer in order to make it move. The forks wouldn’t stay on.

Product looks sturdy. I am not able to use because it is missing all the screw rods that secure it to the bucket.

They work great only implaint is the bucket clamps slip very often and they have warped my bucket other than that its everything i ordered

Do not attach very secure to bucket

The forks themselves are great. They certainly are more than heavy enough for my subcompact tractor. I give them 5 stars for the price. The problem I had was dealing with the company when they did not send enough clamp bolts along in the original order. Communication was slow and seemed like I was dealing with an AI bot in another country with a significantly different timezone. After much unnecessary back and forth I received the missing parts exactly 1 month after the initial order shipped. The forks were useless to me without the parts. Customer service is not what this company is about but I guess that's what you get for the price.

Not the best quality for the money....

They're ok for what they are. They definitely do not replace a dedicated fork lift attachment for a tractor. Can't hardly see them for the bucket being in tne way.

After installing these forks and using them for a while I have found them to be useful but really only because I only have a few things that require forks to lift. The most I am lifting are loads of about 500lbs. I must say that the fork itself feels very sturdy and they seem to be built like a tank. I say "seem" because unlike actual skid steer or similar forks these are made from rectangular box section rather than solid steel plate. Although they are heavy it is difficult to know the wall thickness of the box section and you are limited as to what you can pick up with these forks due to their very thick cross section. These forks will not fit under certain palettes. Again they have held up well with the loads I have lifted but I do not use palettes. These forks also stick out a long way in front of the bucket (in my case 60") and my bucket is 3 feet deep. That puts the load you are lifting a long way out in front of the skid steer and all of that load is being applied to only about 8 to 10 inches of the lip of the bucket. It really doesn't matter that they are rated for 4000lbs. The lip of the bucket will fail long before that 4000lbs could be lifted. The method by which they attach to the bucket is adequate for light loads but it is very difficult to attach the forks securely to the bucket. The large slot at the end of each fork slides over the lip edge of your bucket. Two "L" handle bolts on each fork fasten down on to the "lip" of the bucket clamping the forks in place. This is problematic for several reasons. First there are flared nut fittings that screw on to the ends of the "L" bolts where they clamp down on the bucket. One must be very careful to ensure these nuts have not travelled up the shaft of threaded "L" bolts while tightening. If they have it will be the sharp end of the "L" bolt that bites in to the surface of your bucket rather than the flared foot of the nut. Getting the "L" bolt tight enough while ensuring the flared nut is properly positioned to tighten against the bucket surface is difficult. Before I figured out that the flared nuts were NOT captive on the end of the "L" bolt, I had driven the end of one of the bolts half way through the surface of the metal clamping plate they give you to put between the bucket surface and the bolts. It is also difficult to tighten the "L" bolts enough to secure the forks in place. It is also important to install the forks over the bucket wear bands. This gives them something stronger to press against rather than just the sheet metal of the bucket. All in all these should be considered an inexpensive alternative to proper skid steer or tractor forks and only for light loads. I bought these because I could get them quickly and they allowed me to get my job done while waiting for my actual skid steer forks to arrive. Big difference between these at $175.00 vs. my skid steer forks at $2000.00.

Ce lève-palettes est très efficace et me convient parfaitement. Toutefois, j’ai relevé deux points à améliorer : 1. L’écartement des lames est trop large, ce qui oblige à prendre les palettes par le grand côté et empêche de les saisir normalement. 2. Les tiges en fer servant à l’accroche présentent beaucoup de jeu, car elles ne s’insèrent que dans un seul trou. Il serait préférable d’ajouter une deuxième plaque, décalée de quelques centimètres, afin de pouvoir insérer les tiges dans les deux plaques et ainsi éliminer ce jeu