Kundenbewertungen für VEVOR Metalldrehmaschine 17,8x40,6cm Drehbank Metall 50-2500U/min Tischdrehbank Tischdrehmaschine 800W 9x metrische (von 0,5 bis 3 mm) 10x zöllige (von 10 bis 44 TPI) Gewinde MT5 Spindelkonus

Very capable small machine. I am very satisfied with the overall product. I do however recommend a complete reassembly of the machine when it first arrives to clean parts and make small adjustments. Working with non-ferrous materials is easy. It's only when working with steel where the limitations start to show. But by locking the gibs you can make the machine stiff enough to do parting opertation in steel parts but it will take longer than on a bigger machine. Same goes for thread cutting and boring. The motor runs quiet and has good power, it does however start cogging at low RPMs. If you engage the feed the gears can be a bit more noisy but they are easy enough to adjust so they run smoothly. My only real issue is with the tailstock. It is meant for a smaller machine bed and does not sit properly on the ways. Also, the thread cutting table is incorrect. There are better combinations of the included gears for most of the thread pitches shown in the table, I recommend doing the calculations yourself. There are also some cost saving measures that you should be aware of before buying this lathe. This is not meant as a critique, but I just wanted to state that some parts will have some optical damage. I suspect these were rejected by other brands which is why this lathe is comparatively cheap. I have not noticed any negatives with the functionality of these parts despite the smaller marks. Lastly, there is no handwheel dial on the main saddle. This is why I recommend installing a DRO for ease of use. For other upgrades I recommend making an actual round handwheel for the cross and comound slides yourself once you have the lathe. This makes feeding per hand a bit easier in my opinion. I also needed to install a few shims underneathe the saddle (between the carrige and the apron) the to get a smoother sliding action along the ways. You can also make a small cover for the apron so that chips don't get between the gears. I would recommend this machine for hobbyists such as myself.

De draaibank werkt naar behoren de kwaliteit is goed hier en daar wat aandacht punten die ik zelf naar mijn eigen zien heb kunnen maken. Ik ben er heel erg blij mee

A bit dissatisfied with low rev limit. Needs mechanical tuning/ surface matching. Good price!

Bin sehr zufrieden damit, danke

Technically fine. Motor control is faulty. It reacts late to the speed controller (potentiometer), so it starts jerkily. Unstable rotation during work. You can't turn it on with the green button, You can't turn it on with the green button.The green button puts it into operation by default,and then the direction of rotation can be selected.After every "F" or "R" switch off, the machine switches off completely, in all such cases, it must be put into operation with the green button.This does not ensure continuous work.The control panel is likely to be defective, Since the machine is under warranty, I do not perform measurements in the control unit.I have notified the technical team, I am waiting for their reply.Overall, the machine is good, so it is recommended for purchase.Service help, I will see how helpful they are.

Buon prodotto, peccato non abbia la torretta porta utensile regolabile in altezza, per centrare gli utensili e il carrello parallelo non si può inclinare per poter tornire la diagonale

Je suis encore en train de le tester mais je suis satisfait de cet appareil après avoir resserré les vis quelques fois la machine s'est améliorée, bien sûr il y a quelques petits écarts à resserrer, le moteur est puissant et dans l'ensemble c'est un bon achat à mon avis rapport qualité/prix.

Per il prezzo ha soddisfatto le mie aspettative. Per il fai da te ed uso hobbistico fa il suo dovere. Servizio assistenza ottimo, subito presente per risolvere eventuali problemi, nel mio caso con un po di pazienza mi hanno spedito un ricambio. Se ne avrò necessità comprerò ancora Vevor. Grazie

un tour intéressant par le fait de ne pas avoir d'entrainement par courroie, le moteur est sur la broche directement, déroutant quand on tourne le mandrin, on sent les aimants. Le fait d'avoir un cône morse n° 4 dans la broche permet le montage d'une pince ER 40 si on souhaite prendre des pièces importante avec une concentricité de +/-0.01 mm (la broche a cette concentricité). Le mandrin trois mord a une concentricité de +/-0.1mm qui est normale. Le tour est quasiment opérationnel "sortit de boite" néanmoins je conseille son démontage pour un ébavurage et un graissage complet.

trés bon mini tour .hélas arrivé abimé .mais j'ai réussi a le dépanner