Kundenbewertungen für VEVOR Papierschneider manuelle Schneidemaschine (bis A3 Papier, 400 Blatt Kapazität), Papierschneidemaschine Hebelschneider, Guillotine-Schere für Papier höchste Präzision Büro Zuhause Schule

Velice nekvalitní, nedá se řezat ve vrstvě, řezaný papír je posouván nožem o přes silné utažení přídržnou lištou. Nespokojen.

The product I received does not match what was advertised. Several components are inferior—for example, instead of a fixed bar to stabilise the paper, it uses a magnetised bar that constantly shifts position. The biggest issue, however, is that it simply DOES NOT CUT PROPERLY. On the rare occasions it does cut, the results are inconsistent and it often fails to cut through the entire stack of paper. What makes this even more frustrating is that the product arrived with a sticker stating it had been tested at the factory. Given that it does not function correctly out of the box, that claim is difficult to believe. A product like this should arrive ready to use and perform its basic function without requiring manual adjustments. Instead, I had to hunt down a vendor video to find adjustment instructions, as no assembly instructions or instruction on how to adjust it was included in the box. Even after following those adjustments, the cutting performance remained poor and inconsistent. Save yourself the frustration and don't waste your time on this product. I will be seeking a refund.

Product *works* out of the box, instructions were simple to follow, didnt actually need them to use. Safety mechanism failed within days, but that does not stop the tool from working. still functions as a cutter. Issues: 1. The fence that comes pre-installed on the base of the machine is not square to the cutting blade or the printed grid on the tool so cuts are never truly square, and this cant be adjusted as the fence sits in pre cut slots and the bolts are only there to lock it down. 2. The cutting stick that sits under the blade sits proud of the level of the base. so when the paper is sitting flat on the base of the machine, the edge being cut is slightly raised up. so once the cut has been made, if cutting "blocks" of paper, the cut is not vertically square as the paper has been skewed up. There are adjustment bolts that screw in underneath the rubber, but even backed all the way out/removed, it still sits proud. Overall the product is functional. If you are a hobbyist and don't need millimeter perfect angles/cuts, its perfectly adequate. But thats about as far it goes. Adequate.

I’m not completely satisfied with this knife. The cutting is not as precise as it should be, and one part of the blade doesn’t cut all the way through, which I had to adjust myself. Paper can sometimes slip under the guard (or guide), which affects the accuracy of the cut. The knife is quite solid and feels sturdy at first, giving the impression of a high-quality tool. However, for the type of work it’s intended for—where every millimeter matters—it really should be much more precise.

Virker som den skal

No se si le pillaremos el punto de cortar con la medida exacta, (pues el tope trasero no es muy fiable) ni a cortar tantas hojas como dice, pues aunque sean cincuenta hojas de papel de 80 gramos y apretando bien el pisón hay variación de arriba a bajo.

Product would be great with a few improvements. The back guide needs to be longer going to the opposite side with a clamp or similar screw down guide like opposite side. When you tighten the clamp holding a larger stack of paper in place to cut, the action of the blade pushes the back guide and you get an uneven cut. If you tighten the clamp extra tight that gives you a wrinkle in the stack. I bought some heavy duty magnets to compensate but it is inconvenient when trying to make minute adjustments. The grid doesnt allow for the 1/8" difference between the clamp and the actual blade cut so you need to adjust for this in your measurement. It is best to draw out a cut line and lower the blade somewhat to see if it matches up.

Lieferung ist heute angekommen, pünktlich. Schachtel weist keine Beschädigungen auf. Beim Aufstellen fällt auf, dass die Schneidemaschine nicht gerade steht und wackelt. Jetzt fehlt doch bei der hinteren Ecke der Fuss, die Ecke ist verbogen und es sieht nach einem Sturzschaden aus. In der Schachtel befinden sich keinerlei Bruchteile des Fusses. Der schützende Sagex war vorhanden. Es sieht so aus, als ob beim Verpacken in China das Teil auf den Tisch geknallt ist, den Fuss verlohren hat und trotzdem eingepackt und verschifft wurde. Da staunt der Laie und der Fachmann wundert sich...

Dear Sir or Madam, I am writing to make a complaint about a paper cutter blade I recently purchased from your company. In general, the blade cuts well through about 90% of the sheet. However, in the upper corner—near the handle that is pressed to cut—the blade consistently fails to cut the last part of the paper. About 10 cm of the last two sheets are left uncut every time. Because of this, I have to finish the cut using scissors or a smaller cutter. This defect is causing constant interruptions in my work and is seriously affecting my productivity. I bought this product to speed up and improve my work, but due to this fault, it is not performing as expected. I feel disadvantaged by this issue and would appreciate a solution, such as a replacement, repair, or refund, according to your warranty or customer service policy. Thank you for your attention. I look forward to your response.

Ich würde dieses Gerät nicht für den professionellen Einsatz empfehlen. Die Qualität ist extrem schlecht; es erfüllt einfach nicht seinen Zweck. Ich habe das A3-Format gekauft. Beim Schneiden eines A4-Blatts beträgt der Fehler bereits 1,5–2 Millimeter. Wie Sie auf dem Foto sehen können, habe ich Streifen mit den Maßen 40 x 297 mm geschnitten, und je länger das Material, desto größer wird der Fehler. Außerdem knittert das Papier gnadenlos. Dieses Gerät ist für ein Spielzeug zu teuer und für professionelle Zwecke überhaupt nicht geeignet.