Kundenbewertungen für VEVOR Bauventilator 367-W-AC-Motor Baugebläse 2800 U/min Baulüfter Gebläse 2574 CFM (4373 m3/h) Axiallüfter mit 10 m Schlauch Axialgebläse 79 dB Geräuschpegel Industrielüfter

assez bruyant

Laut aber wirksam.

Je l utilisé pour cabine de peinture et c est parfait 👍

Preis-Leistung in Ordnung. Saugt ab aber im direkten Ansaugbereich offenbar Verwirbelung was dann zur Staubverteilung anstatt zur Absaugung führt. Die Absaugung funktioniert für den Raum/ Baustelle gut aber nicht als Direktabsaugung an der Entwicklungsstelle.

παρά πολύ καλή αγορά για την δουλειάτου...το συστήνω ανεπιφύλακτα...ελπίζω μόνο να αντέξει στον χρόνο..

Bonjour, Pourriez-vous me faire parvenir la facture de cet achat. Par avance, merci. Bien cordialement f.billon@cabinet-billon.fr

This turned out to be a good purchase. The fan feature works well,, the noise level is right at tolerable if you’re running it in the same location that you’re working in and the room size is a conventional room in a residence. If you’re running the fan on the opposite side of an exterior wall, it’s obviously more tolerable. As far as features, it’s hard to rate higher than a four, because there aren’t any features beyond the on/off switch and the GFCI reset switch. The fan draws enough air to clear smoke and Sheetrock dust effectively, as long as you’re providing enough air for it to move out. The fan is only set up to pull air at the end of the ventilation tubing and NOT PUSH IT, but I did have to utilize it as a push because of environmental circumstances and it performed ok as well with no detectable added strain to the motor. You just need to ensure that you tie the tubing to the fan casing well, because it’s not flanged like the intake, but it does have a rolled edge. I also secured around the guard for the trigger just to be certain it didn’t work itself free and blow the tubing through a window or something. The fan seems to be built well, but there’s not a whole lot of building involved. The casing is steel with rolled edges, intake is flared to connect tubing, functional GFCI switch inline, orange paint that helps with visibility, an on/off switch, removable steel grates on either end to facilitate cleaning and any maintenance or necessary repair, thick plastic fan blade and rubber feet for traction. You should be sure to clean as necessary, especially when you have it moving dust or things of that nature, and I had an old nylon bag that wasn’t being used to throw the tubing into, as well as a small leather belt that I got to run through the tubing and latch to make it easier to carry with the fan. Fan weighs 26.2 lbs carry weight total as I have it set up to travel, and depending on what I’m using it for, I usually keep a 13 gallon trash bag as well to put the vent tubing into until I can get home and rinse out any dust that may have accumulated inside.

get one with a 2 way switch for motor, but they won't disappoint.

Very good fr the money

Einfaches aber leistungsfähiges Gerät. Robust aufgebaut. Ich benutze es, um beim Schleifen oder Sägen in meiner Werkstatt den Staub abzusaugen, da ich keine feste Absauganlage habe. Das einzige Problem, das mir aufgefallen ist, besteht darin, dass es am Rand des Ansaugstutzens eine Verwirbelung gibt, die entgegen der Ansaugrichtung läuft, d.h. in einem kleinen Bereich um die Rundung scheint das Gerät zu blasen anstatt zu saugen das Gerät. Darauf sollte man bei der Aufstellung achten, damit anfallender Staub nicht in den Raum geblasen wird, anstatt abgesaugt zu werden.