Kundenbewertungen für VEVOR Presswerkzeug und Akku-Set, Rohrpresszange, elektrisches Rohr-Crimpwerkzeug mit M15-, M22-, M28-Backen, Presswerkzeug-Set mit 2 Stück 18-V-2,0-Ah-Akku, Schnellladegerät und Tragetasche

Great tool for the money

It works really well just as described. My only two complaints are they made it huge and heavy so tight overhead areas can be tricky. And the case does not have a cut out for one of the dies so you have to stack it on another one which makes the case not close effortlessly.

I bought this back in August and put it through the ringer. basically, gave it to our least experienced plumber for him to use and abuse. It still works, even after 1000 presses. Battery life too. The molding is starting to peel and Im pretty sure im going to need to find someone to recalibrate it pretty soon. so far, no misfires to the tool. The trigger is still working well. Honestly was one of my concerns since it looked so cheaply made, but all is well. for it's price especially, this was well worth it.

Overall for the cost of this tool it has already paid for itself. Almost everything plumbing they make a fitting to use. I had 1 failed crimp out of 50. I believe it was more user error and a bad fitting than the tool itself. I will be looking at buying the better one later.

Works well

Tool worked great

Akku mit Kabeln überbrücken damit man an die 3 Kontakte der Platine kommt die unter dem Akku ist mit den Aufdrucken RX/TX/DTC der Pins. Der Reset-Vorgang an den Pins ​Sobald das Gerät Strom hat (Display leuchtet oder LED blinkt), kannst du die Pins bearbeiten. Da es sich um eine serielle Schnittstelle handelt, reagiert die Sperre oft auf Erdung: ​DTC gegen Masse (GND): DTC steht oft für Diagnostic Test Control. Versuche, den DTC-Pin mit dem Minuspol des Geräts (Masse) kurzzuschließen. Oder der Masse des Akkus. ​Halte die Verbindung für ca. 5–10 Sekunden. ​Drücke währenddessen einmal kurz den Auslöser der Presse. ​TX und RX verbinden: Wenn DTC alleine nicht hilft, verbinde TX und RX direkt miteinander (Loopback), während du das Gerät einschaltest. Das zwingt manche Controller in einen Fehlermodus, der den Zähler ignoriert. Alle Angaben ohne Gewähr. Keine Haftung für Schäden. Die Presse sollte vom Fachmann geprüft werden vor allem da die Bolzen mit der Zeit der Nutzung nachgeben.

Extremely disappointed that somehow when I was ordering I must not have been able to hit the extended warranty button good enough so I called before I even received it from FedEx or UPS I can’t remember which delivery service it was asking if I could purchase the extended warranty that same day it was getting delivered and I was told I could not purchase the extended warranty after I paid for the product, almost every company I know will allow you to purchase the Extended within at least a few days of receiving the merchandise

TOOL WORKS GREAT, A BIT HEAVY AT TIMES WHEN YOU CARRY IT OR USE IT BUT NOT THAT BAD. FOR YOUR INFORMATION ITS A GREAT TOOL TO HAVE. IT DOES EXACTLY LIKE RIDGID OR MILWAUKEE'S TOOL FOR MUCH LESS. I HAVE BEEN USING IT FOR TWO YEARS NOW AND ITS STILL DOES A GREAT JOB. THE BATTERIES LAST LONG AND THE ONLY THING ID SAY ITS NOT AS GOOD IT IS THE CASE THAT COMES WITH IT IS BY FAR NOT AS STRONG AS THE TOOL FOR SURE . OVERALL ITS A SWEET TOOL TO HAVE.

Tool has held up for the last 9 months. It is compacted, and works great for its size. I bought two and are both working nice. Would like to by the 1 1/4 head for this kit.