Kundenbewertungen für VEVOR 2x Palettengabeln Anklemmbar 1490x100x230 mm Gabelträger 1814kg Tragfähigkeit Gabelzinken 149cm Gesamtlänge mit 109,2cm-Gabelblatt Gabelstapler Gabelstaplerzinken Frontlader Palettenrahmen

Vraiment très pratique, seul inconvénient on ne voit pas pour entrer sous la palette, il faut descendre de l'engin.

Good to work aroud the house, but falls of easily when you try to get out of an heavy pallet. Overall satisfied

Forks great just dont fit my bucket well because of step on bucket. Other than that no problem If bucket was flat would mount great. I just got to build something so they will clamp more securely.

These 4000 lb. pallet forks should have come with a stabilizer bar to limit side to side movement, the same as the smaller forks. Also, the screw down rods (2 each fork) would be much better with a nut welded to the plate and the rod would then screw down into the nut. As it is the nut is attached to the screw rod, and as soon as the nut reaches the plate, the whole plate slips and slides sideways. This causes paint to be removed from the plate and constant repositioning of the plate while tightening.. This would not happen if the nut were attached to the plate as the rod would hold the nut and plate in place.

They’re ok for light duty work. It’s all a bit wobbly even with the cross brace but again it’s for light duty work. All in all I’m pretty happy with it. The price is good.

Die Palettengabel ist im Großen und Ganzen in Ordnung, vor allem für den Preis. Die Aufnahme für die Schlepper Unterlenker sind allerdings nicht optimal. Ich muss sie für meinen Schlepper noch anpassen. Anstatt 2 Bleche, zwischen denen eine Kugel mit Bolzen befestigt wird, ist nur ein Blech angeschweißt. Mit den mitgelieferten sehr langen Bolzen lässt sich der Rahmen nicht am Schlepper anbringen. Der Bolzen für die Oberlenkerkugel ist sehr lang, es funktioniert aber. Die Schweißnähte an sich sind in Ordnung. Wenn die Gabeln angebaut sind, haben sie leichten Höhenunterschied an der Spitze, ist aber noch im Rahmen. Für die Unterlenkeraufnahmen habe ich mir gesondert woanders schraubbare Unterlenkeraufnahmen bestellt und angebaut, siehe Bilder. Nun Funktioniert es. Alle Bolzeny die mitgeliefert wurde, waren viel zu lang. Diese habe ich gekürzt.

I purchased this pallet Fork Lift and the middle rod has bent, why I don't know. I use it to lift limbs and it supposed to support up to 2000lbs but the middle bar bent. However you decide to handle this is fine with me. Sorry I could only download 2mb of the pic part of the picture

The girls themselves are holding up okay, but the stabilizing bar has already bent and torn. I would also appreciate longer handles to screw this thing into my bucket. Price was decent for what I got. I may as well have opted for the less expensive version without the stabilizer.

I found it to be a great product that is very useful. Must be careful using, it is limited in what it can do. The price is great for what it can do.

The forks are strong and fit over the lip of the tractor bucker well - their is a minor manufacturing flaw and a design flaw: One of the tightening bolts threaded connector to the fork is welded incorrectly causing the side of the bolt to rub against the side of the fork bolt chase see image). The fork screw -down clamp bolts look like they are supposed to have flat contact surface that 'should' allow the bolt to tighten without causing the round contact surface to 'walk' on the bucket. This is a problem and a better contact point could easily be designed that would not walk on the bucket surface (a design that would allow the bolt to tighten without the contact surface turning with it). However, with that said, I greased the bolt into the nut/contact surface and left the bolt about 3/8 inch; from the contact plate which allows for the contact surface to better seat while tightening down the bolt - the contact surface still walks on the bucket, but not as much.