Kundenbewertungen für VEVOR 2x Palettengabeln Anklemmbar 1490x100x230 mm Gabelträger 1814kg Tragfähigkeit Gabelzinken 149cm Gesamtlänge mit 109,2cm-Gabelblatt Gabelstapler Gabelstaplerzinken Frontlader Palettenrahmen

Absolute junk. Dont waste your money

Bestaat uit 2 pakketten, slechts 1 pakket ontvangen, tweede is blijkbaar terug gestuurd naar de handelaar wegens beschadigd onder de baan. Was ook niet duidelijk dat het om twee pakketten ging, dus bij aankomst 1ste al verwarrende situatie. Beter had geweest dat de handelaar direct het tweede pakket had nagestuurd, ipv geld terug en opnieuw te moeten bestellen. Wel geld terug gekregen, wat prima is, maar dus geen werkbaar geheel, de vorken liggen daar nu ...maar vertrouwen kwijt om terug te bestellen ...Immers als je betaalt moet je ook je 3-code meegeven en dat vonden we al scary.

Teleurgesteld. Er is maar 1 pakket geleverd en we hebben dus een incomplete vorkverlenging .We krijgen lastig contact met de klantenservice. We zijn al weken over en weer aan het mailen maar tot nu toe geen oplossing.

I’ve bought a lot from vevor and was happy with products these were a waste of of money no way are they going to stay in position or stay on real heahache

livraison en 2 colis séparé reçu en l'espace de 4 jour par dpd 2 colis endommagé manque des pièces reste a essayer la calité !…

I had to modify the product. As delivered, it doesn't fit anywhere. The welds are incomplete, the workmanship is imprecise. It vibrates when moved. The fork joints are too weak and bend; I had to have a ring welded in between.

Perfect item to have, helped out a lot with the farm so far. I am glad I spent the money. Well worth it

Overall good forks. Welds "look" questionable. Tightening handles which are side by side on each fork...occasionally interfere with each other. A weld on one fork is too high or badly positioned....does not let the fork lie flat....so the weld has to be ground down to allow the fork to sit flat on the loader bucket surface.

Bought with high hopes. The one pin to screw on isn’t screwing on properly. Needed a hammer in order to make it move. The forks wouldn’t stay on.

After installing these forks and using them for a while I have found them to be useful but really only because I only have a few things that require forks to lift. The most I am lifting are loads of about 500lbs. I must say that the fork itself feels very sturdy and they seem to be built like a tank. I say "seem" because unlike actual skid steer or similar forks these are made from rectangular box section rather than solid steel plate. Although they are heavy it is difficult to know the wall thickness of the box section and you are limited as to what you can pick up with these forks due to their very thick cross section. These forks will not fit under certain palettes. Again they have held up well with the loads I have lifted but I do not use palettes. These forks also stick out a long way in front of the bucket (in my case 60") and my bucket is 3 feet deep. That puts the load you are lifting a long way out in front of the skid steer and all of that load is being applied to only about 8 to 10 inches of the lip of the bucket. It really doesn't matter that they are rated for 4000lbs. The lip of the bucket will fail long before that 4000lbs could be lifted. The method by which they attach to the bucket is adequate for light loads but it is very difficult to attach the forks securely to the bucket. The large slot at the end of each fork slides over the lip edge of your bucket. Two "L" handle bolts on each fork fasten down on to the "lip" of the bucket clamping the forks in place. This is problematic for several reasons. First there are flared nut fittings that screw on to the ends of the "L" bolts where they clamp down on the bucket. One must be very careful to ensure these nuts have not travelled up the shaft of threaded "L" bolts while tightening. If they have it will be the sharp end of the "L" bolt that bites in to the surface of your bucket rather than the flared foot of the nut. Getting the "L" bolt tight enough while ensuring the flared nut is properly positioned to tighten against the bucket surface is difficult. Before I figured out that the flared nuts were NOT captive on the end of the "L" bolt, I had driven the end of one of the bolts half way through the surface of the metal clamping plate they give you to put between the bucket surface and the bolts. It is also difficult to tighten the "L" bolts enough to secure the forks in place. It is also important to install the forks over the bucket wear bands. This gives them something stronger to press against rather than just the sheet metal of the bucket. All in all these should be considered an inexpensive alternative to proper skid steer or tractor forks and only for light loads. I bought these because I could get them quickly and they allowed me to get my job done while waiting for my actual skid steer forks to arrive. Big difference between these at $175.00 vs. my skid steer forks at $2000.00.