Kundenbewertungen für VEVOR 2x Palettengabeln Anklemmbar 1490x100x230 mm Gabelträger 1814kg Tragfähigkeit Gabelzinken 149cm Gesamtlänge mit 109,2cm-Gabelblatt Gabelstapler Gabelstaplerzinken Frontlader Palettenrahmen

Ce lève-palettes est très efficace et me convient parfaitement. Toutefois, j’ai relevé deux points à améliorer : 1. L’écartement des lames est trop large, ce qui oblige à prendre les palettes par le grand côté et empêche de les saisir normalement. 2. Les tiges en fer servant à l’accroche présentent beaucoup de jeu, car elles ne s’insèrent que dans un seul trou. Il serait préférable d’ajouter une deuxième plaque, décalée de quelques centimètres, afin de pouvoir insérer les tiges dans les deux plaques et ainsi éliminer ce jeu

The brace bar broke (snapped the weld) on the very first use.

Im Vergleich zur Konkurrenz ist das Teil echt preiswert. Es ist auf jeden Fall nicht billig obwohl es den Anschein hat nicht in Deutschland produziert worden zu sein. Die Ausnahme für den Dreipunkt ist aus massivem Stahl gefertigt. Jedoch wurde bei der Aufnahme für die beiden Kufen doch etwas geschlampt. Die Toleranzen sind zu hoch und dadurch hat das ganze Fuhrwerk zu viel Spiel. Hoffe dass dadurch nicht die Tragfähigkeit leidet. Mit ein paar Unterlegscheiben läßt sich das Problem jedoch in den Griff kriegen. Ansonsten keine Auffälligkeiten. Sogar alle Bolzen mit Sicherungssplint sind mit dabei. Also für den Preis echt ok.

Bought those forkd to install on my bucket and its really hard to get them to be tight. Whrn applying pressure the fork dented my bucket because they cannot be tighten hard enough. I did put the chains, but suggest using ratcheting straps. The is also no cross bar to keep the proper spacing, which is crucial. On install, one of the nut where it contact fell off. Overall, I would not recommand or buy again these ones.

For the price point good buy Material could be stronger Clamping system a little sloppy

1/2 The Hardware is missing. This 4,000 lb model required 4 of the big clamping bolts with nuts. The 2,000 lb model required 2. The box was in good condition so they didn't fall out. The manufacturer didn't put them in the box , or I was sent the wrong item. I checked today for these 3/4 in diameter bolts and nuts found some not rated the 8.8 hardness and there over $21.00 each. What the heck. Seen another review saying the same thing buy the name Richard Waldrop.

Used these to lift some stumps into my backhoe bucket. First stump was around 400 lbs and the forks didn't stay straight even though I tightened them with a mini sledge but they did lift the stump. Second larger stump was around 600-700 pounds and the forks couldn't handle it. Both forks bent and broke. There is no way these things could handle anywhere near 4000lbs. Totally disappointed. While I figured they might not do what they said they would, I was hoping they would be able to handle at least half the rated weight. Save your money and buy something better.

Bought these about eight months ago and the cross bracket cracked the first time I used them. I've only used them a few times since but just did and the bracket broke completely.

Not impressive, their not easily tightened down, the bolts hit each other when tightening, they need to be offset and come with something to get then tightened enough. the grip plates are not attached so using them sucks they slip around, pretty much useless. When you use the stabilizer bar to keep the forks straight you loose like 6" of the forks and they will not extend through the pallet all the way. The actual forks seem to be built ok. overall unfortunately i would not recommend buying these at all. I'm usually really happy with the Vevor products I get, but not with these.

was not able to securely fasten the forks to my loader bucket. I even replaced the tighter bolt with better bolts and it still did not connect properly. so wa s not real able to us the forks