Kundenbewertungen für VEVOR Elektrische Betonsäge, 356 mm, Hochleistungs-Kreissäge 5000 W, Schnitttiefe 127 mm, Nass-/Trocken-Scheibensäge mit Wasserrohr, Sägeblatt, für Stein und Ziegel

ok

De zaag is erg zwaar en moeilijk te hanteren voor een persoon alleen.

Me basta con un magneto de 16A tipo C. En España las condiciones de AC son 230v y 50Hz y, como supuse, los comentarios que decían que necesitaba 30A eran porque en EEUU y Canadá se trabaja casi con la mitad de tensión. La máquina funciona de manera correcta y corta fácilmente muros de ladrillo tosco con cemento y enfoscado. ¡LA HE USADO POCO AÚN! (Por ello sólo las tres estrellas, aunque, en lo que la he usado, merece al menos cuatro) Es un muerto, lógicamente. Olvidaos de cortar por encima de vuestra cintura sin ayuda de un contrapeso que te permita manejarlo con "cierta" seguridad. He logrado hacer cortes en horizontal, pero levanta más polvo (porque el disco se moja menos) y con el sistema contrapeso que he ideado tengo que TENER CUIDADO PARA QUE EL PESO NO REPOSE SOBRE EL DISCO (por seguridad). El sistema de.bomba del agua es lo que menos logrado está, pero funciona y es de gran ayuda sobre todo si no te importa el barrizal que se monta. Espero que siga así.

Will absolutely blow 15 amp circuit. Don't even bother buying it or using it unless you have access to 20 amp circuit. It has a surge protector on the power cord but it's just for looks apparently. Quality seems pretty decent. The plate/shoe is not square to the blade so no sense in putting it on. I also struggle to get it to cut straight down/square. My other saw I can. The water hose is pretty good quality and it's nice that it includes the water pump.

Ich bin zwar kein Elektriker, aber ich frage mich, wo man einen Schukostecker bei 220/230 Volt mit einer Last von 32 A einstecken soll. In der Anleitung steht, man solle die Arbeit in kleinere Schritte aufteilen, falls die Sicherung nicht ausreicht. Etwas anderes bliebe mir auch kaum übrig, wenn jede Sicherung alle paar Sekunden auslöst. Zudem bezweifle ich, dass das verbaute Kabel dieser Last überhaupt standhält.

So... The tool is a 32 amp tool which comes with a 15 amp cord. While it CAN operate on 15 amps, you'll need to reset breakers like crazy (a 2 person operation) and take 1/2" or so deep passes. On a 20 amp circuit, it took 2 hours to cut 19 lineal feet to the full depth in soft, sandy concrete you could chip with a screwdriver. LOTS of passes and breaker resets... The only benefit of the tool was the water feed. It kept dust to a minimum and I loved that. I plan to add a 30 amp breaker to my box when I make the next cuts to see if it may help keep the tool from stopping.

Cuts through 4 to 5 inches of concrete slowly and effectively. Trips the 20A breaker about every three to four minutes of cut time, while nothing else is drawing off the same circuit. A bit frustrating; I tried two different 20A circuits with the same result. The saw does work, but it's frustrating to have to go re-set the breaker every few minutes or, you can stop every two minutes and let the breaker cool down. Either way, it draws too much power for a 20A 120V circuit. If I could do it over again, I'd buy the 12" 1.8 kW saw instead.

It got the job done but takes a while as the motor overheats and blows 20 amp breakers with a heavy gauge cord

I contantly blew a 20 amp breaker. We needed to switch to a 30 amp breaker to run saw. It was blowing the 30 amp breaker but ́ot as often. Then the in line reset on the saw cord got very hot. After cutting that off cord and replacing the end the saw ran great. No more problems with blowing the breaker

saw cuts well not a fan of the water hookup should have a hose connection instead of that mickey mouse pump you have to put in a bucket of water. also dont think thats very safe