Kundenbewertungen für VEVOR Schwenkbarer Frästisch, 25.4x17.8 cm(10 x 7 Zoll), Schwenkwinkel-Fräsmaschine, 0 – 80 °, verstellbare Schwenkwinkelplatte mit 3 T-Nuten und einer verstellbaren Kurbel, robuste Schwenk-Fräsmaschine zum Schleifen

Lieferung sehr schnell! Es gibt einige scharkantige Stellen welche etwas nachgearbeitet werden müssen. Ansonnsten ist der Frästisch eine Bereicherung für die Werkstatt

Der Schwenktisch ist für den günstigen Preis gut verarbeitet Etwas entgraten was man in China nicht kennt, aber das bin ich gewohnt Dann kann man damit arbeiten

Très beau produit 5 sur 5 Petit bémol pour l'usage en fraisage 4,5 sur 5 car la précision de table est de 0,05 mm. C'est déjà pas mal. Merci

Preis-Leistung absolut ok Verarbeitung und Toleranzen für Hobby Anwender absolut ausreichend. Mit etwas Nachbearbeitung ( entgraten ) absolut top. Kundendienst in Anspruch genommen - schnelle und freundliche Hilfe.

Schnelle Lieferung alles Top

I contacted Vevor before purchasing my 10" x 7" tilting angle plate concerning a review about unfinished saddle surfaces and was assured they have stringent quality controls. When it arrived I was very pleased with the way it was packaged in double boxes with the angle plate oiled and double wrapped in plastic. Top was ground, bottom appeared to be ground, degree increments were clean and concise. For the price I was very happy but I still wanted to check it out further. It was set and locked on o degrees so I placed it on my bench top mill table which was trammed in at .002 for a 7 3/8" circle. The first thing I noticed was it rocked diagonally so I flipped it over on it's top and got the same results. Next I clamped it down on the table and ran the four corners setting the first corner at 0. The remaining four corners were .005" of an inch higher (see pic). Next I noticed the the outer corners of the top saddle were not in contact with the base saddle (see Pic). Finally looking at the saddle surfaces they appear (my opinion) to have been cleaned up with a sanding disc on an angle grinder, the same for the two long sides of the top plate(see Pics). For most of what I do for $104 this will suffice, but for some more precise I wouldn't recommend it. With all that said I'm pleased enough to keep it and possible attempt to bring it in closer latter on. I've been a machinist for 40 years working at McDonnell Douglas and Boeing. Sorry two pics would not load.

Solved my problem an easy way to set up à angle on the mill leaving the table settings alone, as with any new tool you just have to learn it's benefits and limitations. Top and bottom are reasonably parallel in the lengthwise direction, the surface is flat and the sliding surfaces glide smoothly. Remember to tighten the brake/holding screws before aligning with the dial gauge, there is a little play. The degree division at the end is only a guide line and only for an approximate setting, there is a lot of backlash in the worm gear and it has a slightly rough and uneven gait, but remember to only aproach one way and it will work. All in all, a nice piece of tool for the price.

buona qualità. da aggiustare i giochi e fare buona pulizia iniziale. Facile da utilizzare e buona la precisione.

Bon produit, imbattable concernant le prix et facile à utiliser. Finition très bonne un seul petit default la manivelle n'est pas très adaptée

I didnt expect too much for the price but I was pleasantly surprised. Its well built and without doubt smoother than expected and while the tollerances are off on the scale they are easily corrected. Easily rigged to fit either myfird or boxford and perfectly usable. Happy purchaser.